Description |
This instrument (IPC-1402-P) is designed as a general purpose laboratory power supply. It has two isolated outputs which operate independently of each other.
The AC output is selected by means of a 4-position switch on the front panel. Selected voltages are 2, 4, 6 and 12V at 4A continuously, or up to 5A for periods of 1 hour. The output is supplied via a pair of 4mm sockets on the front panel colour coded white. The output is protected from overload or short circuit by a current sensing circuit breaker mounted on the front panel.
The DC output is smoothed and regulated and is continuously variable from 0V to 12V at currents up to 3A. Voltage ripple typically less than 50mV. The output is supplied via a pair of 4mm sockets on the front panel colour coded red (positive) and black (negative). The output is protected from short circuit or overload by an electronic regulator.
The outputs may be used simultaneously as long as the combined load does not exceed 3A.
Power on is indicated on the front panel by a green LED. An illuminated on/off switch is mounted on the rear panel adjacent to a fused IEC mains inlet. Enclosed in a robust metal case with a durable powder coated finish. Supplied with detachable mains lead and instructions.
A pair of graphs showing how the output voltage of this power supply varies as the current supplied is increased is included in the instruction leaflet for this instrument.
|
A six-decade resistance substitution box designed for use in educational establishments.
|
Pack of 10 12V 21W Small Bayonet Cap (SBC) Radial Filament Lamps.
|
The Powerlock power supply has both a lockable AC and DC outputs ranges by a simple key making it impossible for students to change the voltage. The Powerlock offers 2,4,6,8,10 and 12 in both DC and AC. Outputs may also be used simultaneously up to the rated output required. For safety, the output is also protected by a simple push button cut-out. Each unit is supplied with 2 that can be used on all Powerlock units if needed. Supplied with 2 keys.
|
A compact power supply offering 2, 4, 6, 8, 10, and 12 volts at currents of up to 5A. Both dc and ac outputs may be used simultaneously up to the rated output. The output is protected by a push button cut-out. The unit is 2A fused on the back panel and comes complete with a moulded mains lead and plug. 4 units are designed to fit in a shallow Gratnell tray.
|
A multipurpose unit that allows the user to easily calculate Planck's constant, to measure the wavelength of coloured light, demonstrate colour light transmission through colour filters and show the diffraction patterns for various wavelengths of coloured light using a range of 4 LEDs (Red, Yellow, Green and Blue) covering the light range from deep blue at 470nm to near IR at 940nm.
|
Content |
Description: Dual Output PSU (12VAC/12VDC)
Part Number: IPC-1402-P
Electrical Supply: 220-240VAC, 50-60Hz
Dimensions: 179 x 190 x 85mm overall
Mass: 2.9kg
AC Output Voltage Range: 2, 4, 6 and 12VAC
Maximum AC Output Current: 4A (5A upto 1 hour)
DC Output Voltage Range: 0 to 12VDC
Maximum DC Output Current: 3A
|
- Simulates resistances from 1Ω to 999,999Ω in 1Ω steps
- The required resistance is set by selecting the correct value from six rotary decade switches which clearly indicate the value selected by the student
- An additional 1kΩ resistor is provided connected between one of the terminals of the internal resistance and a third terminal so the unit can be used as an accurate potential divider
- All outputs are on 4mm terminals with 4mm sockets
- Housed in a tough ABS box with non-slip rubber feet
- Voltage rating 250V
- Power rating 600mW
- Dimensions 110 x 75 x 50mm
- Designed and manufactured in the UK
|
Pack of 10 12V 21W Small Bayonet Cap (SBC) Radial Filament Lamps.
|
- Output voltages AC & DC
- 2,4,6,8,10,12 voltage range in AC and DC
- Current 5A
- Voltage type - Stepped
- Output type - Full wave rectified, non-regulated
- Push button trip reset
- Mains input 230/240V AC, 50Hz
- Supplied with mains plug and lead
- Manufactured in the UK
|
Specification
- Input Supply voltage 230V dc
- Supply frequency 50Hz
- Mains fuse Rear panel 2A, 20mm quick blow Mains plug 3A
- Output Voltage 2, 4, 6, 8, 10, 12V ac nominal 1, 3, 5, 7, 9, 11V full wave rectified dc nominal
- Maximum output current 5A ac or dc
- Manufactured in the UK
| Box mounted with 5 x 4mm sockets for attachment to an ammeter or voltmeter to display measurements. Monitoring the voltage of each LED a graph of energy input as a function of light frequency emitted can be measured with an approximate value of Plank's constant calculated.
- Supplied with 500 lines/mm diffraction grating
- Designed and manufactured in the UK
|